for119@gmail.com,
trn114@nate.com
(대용량 파일)
|
ADMIN | 2021-06-16 00:25:15 |
원문
Dark signal calibration consists in determining the following two parameters of the Sentinel-2 radiometric model: o DS(p,j,b,d) of the Sentinel-2 radiometric model which corresponds to the dark signal of the pixel p in channel b, for chronogram sub-cycle line number j (j is within 1 to 6). o DSVCU(p,b,d), which is the dark signal corrected by the MSI VCU (Video Compression Unit) and re-introduced by the ground processing.
3.2.2.5.1.2 Method Description Dark Signal Calibration will be performed through the processing of images with the lowest possible incoming radiance. This is achieved by acquiring images during the eclipsed part of the orbit of ocean targets at night. Acquisitions are as well optimised in order to cover areas without lucent plankton (e.g. South Pacific CEOS test site) and to avoid full moon conditions.
The dark signal is measured using at least 8 seconds of acquisition in order to average and therefore reduce the noise (cf. [E2EPB]). Measurements are averaged for each detector chronogram sub-cycle, producing 6 different dark signal estimations for 10m channels, 3 for 20m channels and 1 for 60m channels.
The dark noise of each pixel is characterised at the same time from the standard deviation of the measurements, and is used within SNR Validation activity for updating the SNR model (see section 3.3.2.7).
The dark signal calibration will be automatic and data-driven based on the reception of the Dark-Signal Calibration data that will be commanded as baseline every two weeks and acquiring 8 seconds each time.
After decompression of the Level-0 product, the dark signal image is averaged over the lines modulo m with m=6 for 10M bands, m=3 for 20M bands and m=1 (i.e. over all lines) for 60m bands. This translates, for 10m bands, in the following equation: |
번역본
암 신호 보정은 Sentinel-2 방사선 측정 모델의 다음 두 파라미터를 결정하는 것으로 구성된다: o 크로노그램 하위 주기 라인 번호 j (j는 1~6 이내)에 대해, 채널 b에 있는 픽셀 p의 암 신호에 해당하는 Sentinel-2 방사선 측정 모델의 DS(p,j,b,d). o MSI VCU (비디오 압축 유니트)가 수정하고, 지상 처리가 재도입한 암 신호인 DSVCU(p,b,d).
3.2.2.5.1.2 방법 설명 암 신호 보정은 가장 낮은 입사 광휘를 가진 이미지의 처리를 통해 수행한다. 이것은 야간에 바다 표적 궤도의 그늘진 부분에서 이미지를 획득하여 달성한다. 획득은 야광성 플랑크톤이 없는 지역 (예: 남태평양 CEOS 시험 현장)을 포괄하고, 보름달 상태를 피하도록 최적화되어 있다.
암 신호는 평균을 내고 소음을 줄이기 위해 최소 8 초의 수집 시간을 사용하여 측정한다 ([E2EPB] 참조). 측정치는 각 탐지기 크로노그램 하위 주기에 대해 평균하여, 10m 채널에 대해 6 개, 20m 채널에 대해 3 개, 그리고 60m 채널에 대해 1 개의 서로 다른 암 신호 추정치를 각각 생성한다.
각 픽셀의 암 신호는 측정치의 표준 편차에서 동시에 규정하며, SNR 모델의 업데이트를 위한 SNR 검증 활동 내에서 사용한다 (섹션 3.3.2.7 참조).
암 신호 보정은 2 주마다 기준선으로서 명령을 내리고 매번 8 초 동안 획득하는 암 신호 보정 데이터의 수신을 기반으로 하는 자동 및 데이터 기반 활동이다.
레벨 0 결과물의 압축을 해제한 후, 암 신호 이미지는 10M 대역의 경우 m=6, 20M 대역의 경우 m=3, 그리고 60m 대역의 경우 m=1 (즉, 모든 라인)의 모듈로 m 라인에 대해 평균한다. 이 평균한 이미지는 10m 대역에 대해 다음 방정식으로 변환한다: |